Dark bronze standing seam metal roof on a new farmhouse style house in Gretna, long panels running from eave to ridge, snow guards above the front porch

Standing seam metal roofing in Papillion, NE

A standing seam roof is steel panels that run from the eave to the ridge in one piece, joined by raised seams with the fasteners hidden under them. There are fewer parts for water to get past, and in hail country many homeowners like what steel does in a storm. Dana walks you through panel gauge, seam height and color, and the crew lays out, flashes and trims every panel for your roof.

  • Panels that run eave to ridge in one piece
  • Concealed fasteners, no exposed screws to reseal
  • Flashing and trim made for your roof

Or call or text 402-555-0163

Ask about a metal roof

We answer the same working day. After a hailstorm, into the evening.

Water coming through a ceiling right now? Call or text: 402-555-0163

Fewer parts between the gutter and the ridge

A shingle roof is hundreds of small pieces, each lapping the one below. A standing seam roof is a few dozen panels, each running the full length of the slope from the eave to the ridge. The seams stand up above the flat of the panel, so water runs down between them and never reaches a joint, and the clips that hold each panel down sit hidden under the seam.

The parts a metal roof still has are the ones we look at on every inspection: the eave trim and drip edge at the bottom, the flashing at walls, chimneys, pipes and skylights in the middle, and the ridge cap at the top. On a metal roof each of those is bent from the same steel as the panels and fitted to your house.

“We wanted a metal roof on the new house that would shrug off hail. Dana walked us through panel gauge and seam height, and the crew ran standing seam over the whole roof, snow guards over the deck. In a storm it is no louder than our old shingles were, which surprised us.”
Ben R. Standing seam metal roof, Gretna Sample review,

Book a gutter to ridge roof check

Close view along the raised seams of a dark bronze standing seam roof in Gretna, the panels running down to a crisp eave trim and gutter

What you choose on a standing seam roof

We bring samples and walk you through each choice on your own house.

Panel gauge

The thickness of the steel. Thicker steel resists denting and oil canning better and costs more.

Seam height and type

Taller seams lift the joint further out of the water. Some seams snap together, some are mechanically folded shut.

Panel width

Narrower panels look tighter on a small roof and show less waviness in the flat of the panel.

Color and finish

Painted finishes in dark bronze, charcoal, black and many others, chosen from samples held up against your siding.

Snow guards

Placed over doors, decks and lower roofs where sliding snow would land.

Underlayment

A high temperature underlayment under the steel, and ice barrier at the eaves.

How a standing seam roof goes on

From the eave to the ridge, like every roof we build.

  1. Tear-off and decking.

    Down to the deck, soft sheets replaced.

  2. Underlayment and ice barrier.

    High temperature underlayment over the deck, ice barrier at the eaves.

  3. Eave trim and the first panel.

    The layout set square so every seam runs true to the ridge.

  4. Panels, clips and flashing.

    Each panel clipped down, flashing bent and fitted at every wall, pipe and skylight.

  5. Ridge cap and snow guards.

    The ridge closed off and vented, guards placed, the site swept.

Book a gutter to ridge roof check

Metal roofs and hail in eastern Nebraska

Hail is the reason most people in the metro ask us about metal. Storms with baseball size hail have crossed the Omaha metro, as the National Weather Service in Valley recorded on June 29, 2017, and the state's record stone, 7 inches across, fell at Aurora in 2003. Steel does not bruise and lose granules the way an asphalt shingle does.

That does not make it hail proof. Large stones can dent a panel, and whether a dent that keeps water out is covered depends on your policy, so ask your insurer before you choose. Some metal panels carry a UL 2218 impact classification, the same test that rates shingles, but UL recognizes a panel as classified only when its label is attached. When we quote a panel, we show you its label and its paperwork, and we write down exactly which panel and gauge goes on your roof.

If you are weighing metal against impact rated shingles, we price both on separate lines. See roof replacement for the shingle side, and hail and wind damage if a storm has already hit the roof you have.

Questions about metal roofing

Is a metal roof louder in the rain?

Over a solid deck and underlayment, as we install it, most homeowners notice little difference from shingles. Metal over open framing, like a barn, is the loud kind.

Will hail dent a metal roof?

Large hail can dent steel, and a dented panel may still keep water out. Some metal panels carry a UL 2218 impact classification; UL does not recognize a panel as classified unless its label is attached, so we show you the label for the panel we quote. Ask your insurer how it treats cosmetic dents on metal, because policies differ.

Can metal go over my old shingles?

We tear off to the deck. That lets us check and replace soft decking and put down an ice barrier at the eaves, and the code does not allow a new covering over a roof that already has two layers.

Do I need snow guards?

Snow slides off steel in sheets. Over a door, a deck, a walkway or a lower roof, snow guards hold it in place to melt. We place them where a sliding sheet would land on something or someone.

What about exposed fastener metal panels?

Exposed fastener panels are screwed through the face, with a rubber washer under each screw. They are common on sheds and farm buildings. On a house we install standing seam, where the fasteners sit under the seams and there are no washers to wear out.

Call or text 402-555-0163

Dana lays out every panel herself

We work from our Papillion office across Omaha, Bellevue, La Vista, Gretna and Council Bluffs. Thinking about a skylight under the new roof? See skylights.

Dana Novak, owner of Marlowe Hill Roofing, in a chalk blue work shirt with a harness over one shoulder, standing by a ladder at a brick house

Dana Novak, owner and roofer

Dana climbs every roof herself, walks each slope from the gutter to the ridge and writes the report you get. She has roofed in the Omaha metro for eighteen years.

Ask about a metal roof

We answer the same working day. After a hailstorm, into the evening.

Water coming through a ceiling right now? Call or text: 402-555-0163

View along a roof ridge at sunrise over Sarpy County rooftops, a standing seam roof in the foreground and the Omaha skyline faint on the horizon

Tell us about the house

Give us the address, the roof you have now, and what draws you to metal: hail, looks, or fewer parts to look after. A photo of the house helps us bring the right samples.

Book a gutter to ridge roof check

We answer the same working day. After a hailstorm, into the evening.

Water coming through a ceiling right now? Call or text: 402-555-0163

Call or text 402-555-0163